THREE-POLE KNIFE-BLADE FUSE BASE

Used for protection of electrical networks from short circuiting and overloads.
Note: Protective elements are delivered separately and are used as additional protection for accidental contact with parts under voltage.

SINGLE-POLE KNIFE-BLADE FUSE BASE

Used for protection of electrical networks from short circuiting and overloads.
Note: Protective elements are delivered separately and are used as additional protection for accidental contact with parts under

HANDLE FOR KNIFE-BLADE FUSES

Used for placing and removing knife-blade fuses NV-00 to NV-03. The handle is made of insulated thermoplastic and can be used without protective gloves.

SLOTTED PVC CABLE RACEWAYS

Slotted PVC cable raceways are very convenient for cable laying of on-wall installations in offices, laboratories, workshops etc. They facilitate easy installation procedure, swift replacement in case of damages and malfunction and supplementary cable laying. They can secure good mechanical protection for electrical lines. They assure good visibility and give a good esthetic look. They can be installed on every surface, horizontally and vertically. They are very stable and very resistant to chemicals. The sides have cut-outs which can be useful for branching of electrical lines and attaching them to various elements. The sizes of openings are regulated by removing one or more ridges on the sides of the raceways. Raceways are made of very hard, self-extinguishing PVC, with temperature resistance to 70 Co. We standardly produce them in white and grey colors, but customers demand we can produce them in any other color.

CLOSED PVC CABLE RACEWAYS

Used for contemporaneously cable laying of all kinds of electrical, phone, signal cables and other wire installations on the wall. They facilitate easy installation, swift replacement in case of damages and malfunction and supplementary cable laying. Closed PVC cable raceways give a good mechanical protection of electrical lines. They can enable good visibility and give a good esthetic look. They are very stable and very resistant to chemicals. They can be installed on every surface, horizontally and vertically. Branching of the raceways is done by cutting the sides towards the dimension of separative raceway, and during angled turning, the endings of the raceways are adjusted by cutting, to needed angles. The shutter panel is attached from the upper side, without the use of any tools. The endings of raceways can be closed with the same shutter panel. At the end of the shutter panel, cut of the sides appropriate to the length of the height of the raceway and then heat the specific point of bending and make the shaping adjustments. Raceway 30×10 is intended for installations of phone, electrical and computer wiring in offices, laboratories, workshops etc. It has a longitudinal compartment and with its design can fit into every interior design. Construction of the raceways assures very neat handling of phone and computer lines with energy lines. Raceways are

SEALING LID FOR CURRENT CLAMP

It is used for sealing of current clamps. It is made of high quality transparent plastic mass.

CURRENT CLAMP FRS SIX-POLE 16-35/6x(4-16)

It is intended for scheming of measuring and distribution enclosures. Bearing is made of high quality imported plastic mass , self-extinguishing V-0 and heat resistance to 110°C without deformation. Contacts are made of brass profiles which make possible simultaneous connection of aluminum and copper. Clamp bearing is constructed to enable it to place in sequence on all existing rails and can be connected sequentially.

Maximum cross section of main conductors is 35mm2 and maximum cross section of six branching conductors is 16mm2.

CURRENT CLAMP FRS FOUR-POLE 16-35/4x(4-16)

It is intended for circuits in measuring and distribution enclosures. Housing is made of high quality imported plastic mass , self-extinguishing V-0 and heat resistance to 110°C without deformation. Contacts are made of brass profiles which make possible simultaneous connection of aluminum and copper. Clamp housing is constructed to enable it to be placed in sequence on all existing rails and can be connected sequentially.

Maximum cross section of main conductors is 35mm2 and maximum cross section of four branching conductors is 16mm2.

RUBBER COUPLINGS

Made of hard rubber, intended for use with cables of diameter from ø10 to ø20mm. They can be easily cut for a certain dimension of the cable. Instead of rubber couplings, standard FEMAN couplings could used.

• Dimensions: ø 10-ø20 mm
• Package: 100 pcs
• Code number: 5127042

ON-WALL JUNCTION BOX

Made of self-extinguishing PVC. The hard rubber entries can be easily cut for every dimension of cable from 10 – 20 mm. In place of these rubber plugs, FEMAN cable couplings can be used.

• Dimensions: ø70 x 40 mm
• Package: 100 pcs
• Weight: 6, 2 kg/100pcs
• Code number: 5127040