Yearly archives: 2015
Entries found: 10
PULLING GRIP FOR STAINLESS STEEL BANDS
Used for tightening and cutting of stainless steel bands (steel support rings) used for securing equipment to poles. This is a very reliable and practical way for quick and easy securing of brackets, stands, supports, lamps, protection devices, signs, etc. on metal, concrete or wooden pole – supports, making a long lasting, greatly tightened, secure attachment without drilling and welding. This system has long been in use by the electrical industry in the developed countries.
FLUORESCENT FIXTURES WITH AND WITHOUT SHADES
We make open type fluorescent armatures in three standard dimensions: 20W-618 mm, 40W- 1228 mm, 65W-1528 mm.
We make all three kinds for one, two or three fluorescent tubes with or without the corresponding reflector. The lamp housing is made of pickled, profiled sheet metal with baked on white enamel, completely wired in accord with the appropriate JUS and IEC standards. The lights are made with IP 20 protection and enable quick and easy installation.
They are designed for general use areas: hospitals, hallways, passages, warehouses and all other locations where lights are not exposed to great exposure to dust and damp.
Fluorescent lights can be also installed in a linear system which enables quick mounting and is universally accepted. The linear system consists of an upper part (housing of a specified length) and a lower part (tube housing of a specified electrical power). Advantages are: Quick installation, long lasting and simple maintenance. The linear system is made with IP 20 protection and is recommended for use in factories, halls, warehouses and areas where lights are not exposed to great exposure to dust and liquids. If the area is higher than 5 m we recommend using reflectors that direct the light beam from above.
Code number | Type | Power W |
3901020 | FOS -120 | 1 x 2 |
3902020 | FOS-220 | 2 x 20 |
3903020 | FOS-320 | 3 x 20 |
3901040 | FOS-140 | 1 x 40 |
3902040 | FOS-240 | 2 x 40 |
3903040 | FOS-340 | 3 x 40 |
3901012 | reflector | 20 |
3901015 | reflector | 40 |
WATER-RESISTANT FLUORESCENT FIXTURES
DESCRIPTION
Lamp is intended for lighting of industrial objects, especially where there is a greater exposure to damp and dust. The lamp body is made of ABS. The fasteners for securing the cover are stainless steel. The polyurethane gasket is cast directly into a groove of the lamp. Polyamide couplings enable IP 65 protection. The cover is made of transparent poly-carbonate, which is UV stabile, (which means that there will not be any great change in the material due to the effects of ultra-violet light rays). The steel reflection plate is plasticized in white and is UV stable.
|
|
|
|
HALOGEN REFLECTOR 2000W
DESCRIPTION
Reflector can be installed either on a wall or a pole. The reflection surface, (rotationally msymmetric) is made of quality polished aluminum, making very shiny. The light beam is wide and equally distributed, so that the energy expenditure is used to the maximum. Adjustable to all positions as desired. The insulation degree of the lamp is IP54. The reflector is connected to a voltage network of 230V/400V. The recommended diameter of copper cable is 3×2,5 mm2.
- Metal-halogen bulb 2000W
- Condenser 60µF ,400V
All these characteristics make this reflector suitable for a wide spectrum of usage, for both exterior and interior installation, but most often used for illuminating entrances and approaches to factory grounds, sports fields, stadiums, work-shops, displays, hallways, facades, etc.
RECESSED LIGHTS FOR INDIRECT LIGHTING – FUSIO
Represents a new concept in office lighting. Built into ceilings of 600 x 600. Its unique system of indirect lighting provides a comfortable and original space lighting. Made of steel sheet metal, painted in standard white color.
Code number | Power W | A mm | B mm | L mm | h mm | Masa kg |
3900360 | 2 x 36W | 598 | 598 | 554 | 184 | 3,8 |
REFLECTOR for sports fields and industrial illumination
The way the housing is made,(pressure cast aluminum) and the surface protection done by plastification makes this reflector resistant to atmospheric conditions, permitting its use both indoors and outside.
By using anodized, finely polished aluminum for the reflector surface, a better distribution of the light flux is obtained.
The light beam is wide and uniform, so that the energy spent is used to the maximum. Adjustable to all positions as desired.
With its compact and elegant appearance, it easily adapts to all structures, to both modern and traditional architecture.
All these characteristics make this reflector appropriate for a wide spectrum of applications, for both exterior and interior installation, but it is most often used for lighting entrances, displays, hallways, facades, monuments, parks, etc.
- Protection degree: IP 65
- Nominal voltage: 220~240V, 50Hz
- Installed power: 150W,400W E40
- Base: E40
Code number | Type | Power W | A (mm) | B (mm) | C (mm) |
3900196 | Sodium | 1 x 1000W | 600 | 720 | 200 |
3900197 | Metal-halogen | 1 x 1000W | 600 | 720 | 200 |
REFLECTOR for lighting facades, smaller sports fields and large billboards
The way the housing is made,(pressure cast aluminum) and the surface protection done by plastification makes this reflector resistant to atmospheric conditions, permitting its use both indoors and outside..
By using anodized, finely polished aluminum, for the reflector surface, a better distribution of the light flux is obtained.
The light beam is wide and uniform, so that the energy spent is used to the maximum. Adjustable to all positions as desired.
With its compact and elegant appearance, it easily adapts to all structures, to both modern and traditional architecture.
All these characteristics make this reflector appropriate for a wide spectrum of applications, for both exterior and interior installation, but it is most often used for lighting entrances, displays, hallways, facades, monuments, parks, etc.
Protection degree: IP 65
Nominal voltage: 220~249V, 50Hz Installed power 400W
Base: E40
REFLECTOR for lighting billboards, facades
The way the housing is made,(pressure cast aluminum) and the surface protection done by plastification makes this reflector resistant to atmospheric conditions, permitting its use both indoors and outside..
By using anodized, finely polished aluminum, for the reflector surface, a better distribution of the light flux is obtained.
The light beam is wide and uniform, so that the energy spent is used to the maximum. Adjustable to all positions as desired.
With its compact and elegant appearance, it easily adapts to all structures, to both modern and traditional architecture.
All these characteristics make this reflector appropriate for a wide spectrum of applications, for both exterior and interior installation, but it is most often used for lighting entrances, displays, hallways, facades, monuments, parks, etc.
-Protection degree: IP 65
-Nominal voltage: 220~240V, 50Hz
-Installed power: 150W, 400W
-Base: RX7s
REFLECTOR for illuminating billboards, advertisements
The way the housing is made,(pressure cast aluminum) and the surface protection done by plastification makes this reflector resistant to atmospheric conditions, permitting its use both indoors and outside..
By using anodized, finely polished aluminum, for the reflector surface, a better distribution of the light flux is obtained.
The light beam is wide and uniform, so that the energy spent is used to the maximum. Adjustable to all positions as desired.
With its compact and elegant appearance, it easily adapts to all structures, to both modern and traditional architecture.
All these characteristics make this reflector appropriate for a wide spectrum of applications, for both exterior and interior installation, but it is most often used for lighting entrances, displays, hallways, facades, monuments, parks, etc.
- Protection degree IP 65
- Nominal voltage 220~240V, 50 Hz
- Installed power 150W, 400W
- Base Rx7s